Jual Driver Motor DC Hall Brushless 12V-36V 500W Murah
Spesifikasi :
Tegangan kerja: DC 12V-36V
Arus: 15A
Daya: 500W
Tegangan speed kontrol: 0.1V-5V
Proteksi stall
Proteksi arus lebih
Size: 63*42*17mm(L*W*H)
Bisa dikontrol menggunakan arduino
Wiring:
Terminal output power:
VCC (positip power suplai DC 12V-36V)
GND (Gnd power suplai)
MC (motor phasa W)
MB (motor phasa V)
MA (motor phasa U)
Terminal input kontrol:
GND (Gnd arduino)
VR (Variable Resistor atau tegangan analog pwm arduino 0-5V yang mewakili 10% hingga 100% kecepatan motor).
ZF (pin direction motor, logika high untuk CW, logika low untuk CCW).
M (tachometer pulse output, jumlah pulsa output bergantung jumlah kutub motor dan pulse per revolusinya).
EL (pin enable, logika high untuk Run, logika low untuk Stop).
5V (5V arduino).
Terminal input sensor Hall Effect:
5V (Hall positip power)
Ha (Hall signal a)
Hb (Hall signal b)
Hc (Hall signal c)
GND (Hall negatip power)
Kondisi: Baru
Berat: 100gr
Perhatikan: pasang heatsink bersirip untuk mendinginkan bagian mosfet saat beroperasi. Antara mosfet dengan heatsink harus dipasangi isolasi heatsink supaya tidak konsleting. Heatsink dan isolasi heatsink not included
Jual Driver Motor DC Hall Brushless 12V-36V 500W Murah
Jual Driver Motor DC 43A Arduino H-Bridge BTS7960 Murah
Spesifikasi :
The drive uses the full H-bridge driver module power driver chips BTS7960 composed overheating overcurrent protection. Dual BTS7960 H-bridge driver circuit, with a strong drive and braking effect, effectively isolate the microcontroller and motor driver! High current 43A!
Berat: 200gr
Kondisi: Baru
Board features:
1. Double BTS7960 high current (43A) H-bridge drivers
2. MCU 5V isolated, effectively protect the microcontroller
3. Motor can be achieved is to reverse, two PWM inputs highest 25kHZ frequency
4. Isolated chip 5V power (can be shared with the microcontroller 5V)
5. Supply voltage 5.5V to 27V
Aplikasi: driver motor AGV (Automated Guided Vehicle), driver motor kursi roda listrik, driver motor Lawn Mower.
Jual Driver Motor DC 43A Arduino H-Bridge BTS7960 Murah
Jual Driver Motor DC 50A Arduino Shield Dual H-Bridge Murah
Spesifikasi :
Power Vcc (Load) : DC 0V~30V
Recommend power Vcc (Load) : DC 12V~26V
Peak current (Load) : 50A
Recommend max working current (Load) : 20A
Kontrol Vcc : 4V~12V
Kontrol logic TTL : DC 2.5V~12V
Terdiri dari 2 bagian yang independen untuk kontrol 2 output motor putaran bolak-balik (motor dc not included)
Dapat langsung dikoneksikan dengan mikrokontroller AVR / MCS-51 / Arduino / ARM / Rasberry Pi dll
Support PWM / PID / Fuzzy / PID Fuzzy (mikrokontroller not included)
Support sistem auto brake
Dimensi : panjang 6,4 cm x lebar 5,2 cm
Berat : 25 gr
Kondisi : Baru
** Hardware**
4x Infineon Power Mosfet LR7843
Using logic chips for signal isolation, the effective protection of the microcontroller
Using high-quality solid capacitors filtering, superior performance
Notice :
1) Control TTL voltage means the High voltage of the control pins (EN, LPWM, RPWM, DIS).
2) The stable max working current is 20A while load Vcc is between 12V~30V. The current is restricted by heat dissipation. Current, we don’t add any heat radiator on the board. So if the current is over 20A, the heat may melt the soldering tin and cause problems. If you want it working stable at higher current, you should add radiator.
3) Power Vcc is recommended to be higher than 12V if your load is large-current devices. While over 12V, the MOSFET is working fully and its power consumption is small. So the heat will be less. If your load current is not large and just several amperes, the power Vcc can be as low as 3V.
Interface :
We are trying to let this driver be compatible with Arduino and non-Arduino users. We leave holes on the PCB and so mount long-pin felmale hearders to plug in Arduino. If you are non-Arduino user, leave the holes alone.
To improve performance while with large current load. you could add soldering tin on the routs shown below.
Control :
Basically the control is very easy.
* Rotate forward: EN = HIGH, RPWM = PWM, LPWM = HIGH, DIS = vacant
* Rotate reverse: EN = HIGH, RPWM = HIGH, LPWM = PWM, DIS = vacant
* Stop and brake: EN = HIGH, RPWM = HIGH, LPWM = HIGH, DIS = vacant
* Stop but not brake: EN = 0, RPWM = HIGH, LPWM = HIGH, DIS = vacant
* Prohibit : EN = X, RPWM = X, LPWM = X, DIS = HIGH
For Arduino users :
Please Note :
1. Smaller PWM duty will get higher speed.
2. PWM frequency should be 1Khz ~ 60Khz. Smaller frequency could get it work but not in perfect performace. It may increase the module’s resonse time, but very slight in nanosecond level. We can’t sense it. Default frequency of Arduino PWM is 0.5Khz. In our test, the default frequency could get it work very well. But remember, for better performance, the recommended frequency is 1Khz ~ 60Khz. In our library, we set the pwm frequency over 1Khz.
Rangkaian driver motor DC KRI / KRPAI, driver motor DC High Ampere High Torsi, driver motor kursi roda elektrik, driver motor segway, driver motor industrial mobile robot AGV dll
Jual Driver Motor DC 50A Arduino Shield Dual H-Bridge Murah
Vsuplai kontroller : DC 12V (battery not included)
Vsuplai beban : DC 12V – DC 100V
Arus : max 50A
Potensio pengatur kecepatan
PWM konverter (optional)
Komponen driver menggunakan IGBT
Filter elektrik
Aplikasi :
Pengatur kecepatan motor dc high ampere, pengatur kecepatan motor konveyor dc, pengatur motor baling-baling dc, pengatur kecepatan mobil listrik, pengatur kecepatan sepeda elektrik/ e-bike dsb
DEPOINOVASI | SUPPLIER ROBOTIK & SISTEM OTOMASI 